Urinal Plumbing Rough In – Mistakes to Avoid & Proven Techniques!
Urinals are common fixtures found in public as well as corporate restrooms and require unique considerations for aesthetics, flushing, as well as installation, and many other things. Urinal plumbing rough-in requires competence to prevent costly blunders. ‘Urinal plumbing rough in’ involves a number of issues, so don’t worry.
You will learn the definition of urinal rough-in in this post. Learn about its significance as well as the rough elevation of the urinal drainage. Learn the sizes and specifications required for the urinal plumbing rough-in. Discover the processes for installing a urinal as well as how to determine a conventional toilet rough-in.
Toilet Rough In: What is it?
Toilet rough in relates to two aspects the location of the exit hole will be underneath the toilet and the rough in size that determines whether toilets are going to fit in the region.
It might be perplexing to replace a toilet since, logically, you should get another one having a base that is identical in size to the old one. But in fact, what matters is the distance between the outlet and the rear of the seat.
What Does a Urinal Plumbing Rough In Mean?
The water exit (usually) sits below the toilet, and that area is known as the rough-in. However, we won’t be discussing those toilets in this article, even if the rough-in is sometimes in the wall. The span from the outlet’s center to the surface of the wall that faces toward the rear of the commode is the rough-in length.
Why is Good Urinal Rough-in Important?
A precise rough-in size guarantees that your toilet’s bowl and surround will fit when it is installed by leaving adequate room between the drainpipe as well as the wall. Your top goal when buying a new toilet should be to measure and determine the proper rough-in.
Verify all of your measures again. The most important measures you’ll take while evaluating the bathroom are these ones. The bathroom fixture will be adequate and function properly if the rough-in size is accurate.
Because obtaining a permit could also include an inspection as well as approval, it is crucial to strictly adhere to the plumbing and construction codes. This is essential because any changes to the pipes might upset the equilibrium between the sewer and vent portions.
What is the Rough Height of the Toilet Drain?
The urinal rim must be no closer than 17 inches through the completed flooring, per ADA regulations. Installation must be done no lower than 16-7/8 inches beyond the surface of the bathroom floor under CSA B651.
Further, urinals must be wall-hung as well as stall-type and must be at a minimum of 13 1/2 inches (345 mm) deep, measured from the urinal edge to the back of the fixture.
How Big should the Urinal Plumbing Rough-In be, and What Specs should It have?
Urinals come in two varieties: wall-mounted and stall kinds, which extend to the ground.
Urinals installed on walls should have rims that are 17 inches beyond the floor of the bathroom and be surrounded by a 30 by 48-inch vacant area on the ground below. The floor area makes it easier to approach the apartment from the front. Moreover, the privacy screens on the urinals have to be spaced 29 inches away and shouldn’t protrude over the front border of the device.
Additionally, companies, notably Kohler as well as American Standard, construct floor-mounted urinals featuring drains that are 8.5 inches away from the nearest wall. For this, a trap beneath the unit is required to improve draining and get rid of urine odors from the bathroom.
It’s also important to note that wall-mounted restrooms are more affordable in comparison to their floor-mounted equivalents. These fixtures might use 2-inch drains without issue. When the existing toilet vent is beyond the appliance, you are able to put a two-inch pierced can tee.
The urinal flange should be installed with the threaded tip 1/4 inch above the surface of the wall following walling. The bracket should then be supported by a wall.
A Measurement Between the Toilet Flange and the Rear Wall
The most important rough-in measurements are how far it is across the center of the toilet’s flange towards the stud walls beyond it, which ought to be 10, 12, or 14 inches based on the kind of toilet you intend to install. When the toilet is in place, you will need just enough space at the rear of the seat to remove the tank lid; do not press the bathroom toilet too tightly against the surface of the wall.
A Measurement between the Toilet Flange and the Side Wall
Once more, there is no specific municipal plumbing regulation that specifies the exact distance between the rear of the toilet and the ceiling or vanity.
To ensure that you’re happy, you must nevertheless make sure there are at least 15 inches in space on every angle.
A plumber may access the exterior of the bathroom fixture and scrub around it with 15 inches of space if needed.
Distance Between the Front Obstruction and the Toilet Flange
Most of the time, it won’t be a problem how close your toilet sits to an exterior wall. The toilet should not be placed too near the bathroom doorway if there is little space available. So that one can readily enter the restroom, you should keep this dimension in mind while building or changing your toilet.
How Much does a Typical Toilet Rough-In Assess?
Determine the location of the toilet’s flooring bolt. Inspect the foundation of the toilet for tiny bolts or covers. At the rear left and right edges of this fixture, within the trapway, they are typically found.
When the toilet is skirted, check the side that faces the toilet or the area in which the toilet joins the ground for any signs of where the bolts are located. To mark the location of the bolts, think about utilizing painter’s tape.
Assess the distance between the wall and the exact location of the foundation bolts for the toilet. You’ll receive the rough-in measurement of the toilet by doing this. Do not measure from moldings or borders.
When the wall that you are taking measurements of contains baseboards or other moldings, move the starting point of your measuring instrument so it is the naked wall slightly above the molding. For an exact overall measurement, if required, measure the back baseboard’s length (from the outermost point toward the wall).
Look through your work. Double-check what you’ve done if your length is different from the typical 10″, 12″, or even 14″! Avoid buying the incorrect rough-in toilet, which might be a pricey blunder.
What Procedures Must Urinals be Installed In?
Turn Off the Water Valve
Turn down the primary shutoff faucet to stop the flow of water into the space. Next, turn down the urinal’s specific shutoff faucet.
Incorporate Drainage Line
As you attach the drainage pipe as well as the trap onto the wall, make sure all of your connections are solid. Use connections and adapters as necessary to customize the pipe & trap to meet your unique requirements.
Set Up the Toilet
In order to ensure proper plumbing and level placement, lean the urinal upon the structure of the wall, the urinal should be mounted on a wall and fixed using the included clamps as well as brackets.
The Source of Water should be Connected
Utilizing the included connection kit, attach the urinal’s chilly water source to the toilet. Verify the tightness and security of each connection.
Try the Uirinal Out
For a urinal examination, restart the water flow. Purge the toilet and look for leaks. Make necessary adjustments to the connections to stop any leaks.
Last Touches
Install the required fittings after the urinal has been fitted. It could be necessary to paint the partitions and the bathroom fixtures to fit the decor.
Watch this video,
Video Credits – Chuck Barron
You May Also Like
